EFFECT OF APPLICATION of ATOMIUM LUBRICANTS in DIFFERENT NODES of the CAR ENGINE.

Tribotechnical compounds of «Atomium Active Gasoline Plus» series create conditions under which the friction surfaces in engine parts are covered with a metallic protective layer, which has a special structure. This layer partially restores the dimensions and geometry of worn parts, optimizes gaps in friction pairs, keeps more oil on the friction surfaces. This provides the following effects from the application of the compound:

• Increasing capacity and fuel economy - partial restoration of worn surfaces in the cylinder-piston group and ability to better retain grease seal clearances in the cylinder-piston group, обеспечивают необходимую газоплотность. This leads to compression recovering, improves combustion quality. Dense oil layer displaces the friction regime in the direction of the hydrodynamic, which reduces the friction losses. All this leads to an increase of engine power with simultaneous fuel economy on 6-8%.
• Low oil consumption – protective layer restores density in node: cylinder liner - oil ring - piston groove. This improves the removal of oil from the cylinder wall and reduces oil burning in combustion chamber, especially at high engine speeds.
• Noise and vibration levels reduction – recovering of compression in the cylinders leads to smooth engine running. In addition, a dense layer of oil softens work of friction parts. All together, this reduces vibration and noise in the engine.
• Toxicity reduction – recovering of compression and optimization of gaps in the cylinder-piston group improves combustion quality and reduces oil burning in combustion chamber, which decreases exhaust CO/CH emissions.
• Restoration of functional properties of hydraulic compensators – protective layer restores optimum clearances in hydraulic compensators, which normalizes oil pressure and provides quality work of mechanism.
• Increasing the resource of the engine operation – protective layer greatly reduces the wear of the most loaded friction parts, which determine engine life.
• Protection in extreme working conditions – protective layer effectively prevents wear of friction parts at high loads due to the structural features (micro-hardness and micro-elasticity) and retention of larger amount of oil.
• Facilitating engine start up and protection during «cold start-up» – treated surfaces are able to retain the oil layer with the engine off for a long time. This facilitates the first shaft revolutions and prevents increased wear of engine with insufficient oil on friction surfaces at start, which is especially important at negative ambient temperature.
• Protection during active driving – treated surfaces keep a more dense oil layer, which reduces wear and compensates oil starvation during fast increase in engine speed.

In all units with toothed gearing as a result of Atomium application the friction surface of teeth, sliding guides, rolling and sliding bearings is partially or fully restored (except for those already destroyed bearings). In automatic transmission, moreover, the performance of oil pumps and hydro-density of spools (if any) improves, that leads to the recovery of characteristics of gear shift.

Compound "Atomium MGSB" partially restores the dimensions and geometry of worn parts, optimizes gaps in friction pairs, keeps more oil on the friction surfaces. This allows to:

• facilitate gearshift. Optimized gaps give the possibility to switch gears more easier and more accurate;
• reduce noise and vibration levels. Optimization gaps and restoration the optimum spacing in bearings reduce noise and vibration during operation of the gear box;
• increase the car free run (in neutral gear). Retention denser oil layer on the surface reduces the frictional losses and increase free run: movement the car in neutral gear.
•  protect the gearbox against wear. Protective layer on the friction surfaces and dense oil layer substantially reduces wear and increases the lifetime of the unit.

Compound "Atomium AGSB" partially restores worn parts, optimizes gaps in friction pairs, keeps a tight oil layer on the surface of parts. For an automatic transmission this allows:

• Facilitate the gear changes. Optimization clearances in the oil pump of an automatic gearbox provides nominal oil pressure. This reduces the likelihood of shocks and jerks during gear changes;
• Reduce noise and vibration level. Optimization clearances and restoration bearings reduce noise and vibration in gear box;
• Increase free mileage. Retention denser oil layer on the surface reduces the frictional losses and by this increase free mileage: movement the car in neutral gear.

 
Protect the gearbox against wear. Protective layer on the friction surfaces and dense oil layer substantially reduces wear and increases the service life of the unit.

"Atomium AGSB" application in variators allows:

• Restore the chain tension. Restoring cone geometry and retention on the surface of a thick layer of oil, which provides traction in node: chain and variator cones, is able to prevent slippage of the chain.
• Extend the life of the unit. Cones surfaces treated with compound significantly less wear during use. This prolongs the life of the unit.
• Application of compound in new gearboxes reduces the risk of "abrasions" and greatly facilitates and accelerates the process of running-in of parts.

Compound «HPS» partially restores worn parts of the power steering pump parts, optimizes gaps, allows you to keep more tight oil layer on the working surface, clears the slide valve mechanism. This helps to normalize operation of the unit, to restore the pump pressure, which leads to a number of positive effects:

• Facilitates rotation of steering wheel.
• Decreases noise and vibration levels. Restoration of power steering pump and cleaning relief valves decrease noise and vibration levels during operation the power-steering;
• Increases the lifetime of the hydraulic power steering (HPS). Restoration of worn details, protection of the hydraulic power steering against wear in the maximum loadings and high temperature of the environment increase the lifetime of HPS in 1,5-2 times.

Compound "Atomium HPFP" partially restores worn parts and optimizes gaps in plunger pairs and in conjugated friction parts of pumps. This allows to:

• restore pressure. The pump provides pressure within the output operating characteristics, providing fuel spray quality;
• reduce noise and vibration levels of inline and distributive high pressure fuel pumps. Restoring optimal coupling of plunger pairs reduces vibration and in turn the noise of the pump;
• increase the engine power. Fuel supply regeneration leads to increased fuel combustion quality, which provides increased engine capacity.
• decrease fuel consumption. Improving the quality of fuel combustion reduces its consumption by 3% -5%.
• decrease exhaust CO/CH emissions up to 50 %.

Tribotechnical compound "MOTOTEC 4" restores worn parts and protects from wear metal surfaces in friction assemblies. Application of the compound reduces the friction losses, increases power, reduces fuel consumption, noise and vibration.

The compound protects all the friction surfaces in all engine nodes:

• in gas distribution mechanism – in the hydraulic compensators, valves etc.;
• in cylinder-piston group;
• in crank mechanism – in the bearings of the crankshaft for example.

If the gear box is in the same oil pan as the motor, the compound will also treat all gear box elements: surfaces of bearings and gears. At the same time, the compound does not interact with friction clutch, does not change its characteristics as it is made of composite materials.

Tribotechnical compound "MOTOTEC 2" restores worn parts and protects from wear metal surfaces in friction assemblies. Application of the compound reduces the friction losses, increases power, reduces fuel consumption, noise and vibration.

The compound protects all the friction surfaces in cylinder-piston group and crank mechanism.